Good afternoon. Long time use RaceChrono Pro and then decided to splash out EML327 v1.4 Orinigal. Other programs see EML327 fine, but I can not and RC tie in place. tell me what to do ? Change the protocol , it did not help unfortunately. Thank you.
When you say "see" is the problem with configuring the device? Go to RaceChrono > Settings > Device #2, change type to "Bluetooth OBD-II" and then select device. Your device should appear on that list after a while.
The device all to see . When you click the Start GPS is OBDII then quickly turns red and try again to connect . or how can the other way to test the OBDII?
The protocol does not affect the Bluetooth connection. Set that as "Automatic" for now. Make sure you close any other app using the OBD-II adapter, before starting RaceChrono session. If that does not help, try to enable "Bluetooth fix" from expert settings.
Хорошо) поставил отметку на Fix . Вроде бы соединился OBD II и всем поставил RPM, записываю видео но кроме времени скорости и карты нет. а оборотов так и нет. есть какая нибудь инструкция где можно посмотреть как поставить обороты двигателя?
OK, if what I understand you're now connected to the OBD-II, but you do not have all the channels you want? When you start your session there is the red/green button on bottom left of your screen. Press that and a page with all devices and gauges will appear. Next to OBD-II device there is "Fast channels" button. Press that and select your channels. It should have all the channels selectable that are supported by your car.
Hi, are you sure the protocol is correct? Bluetooth connection seems to work now, but not the OBD-II connection to the ECU.
Can you send me the logs?
1) Turn on the "RaceChrono > Settings > Expert settings > Save device output" setting
2) Record a new session with the OBD-II reader configured, and send me the output file from phone's storage: - RaceChrono: /Android/data/com.racechrono.app/files/sessions/session_(date)_(time)/device_(id)_output.obd - RaceChrono Pro: /Android/data/com.racechrono.pro/files/sessions/session_(date)_(time)/device_(id)_output.obd
Sorry about the delay checking the log files! Being very busy lately.
ELM327 v1.4
> ATE0 OK
> OK
> SEARCHING... UNABLE TO CONNECT
> SEARCHING... UNABLE TO CONNECT
> SEARCHING... UNABLE TO CONNECT
> SEARCHING... UNABLE TO CONNECT
> SEARCHING... UNABLE TO CONNECT
Wrong protocol is selected, the OBD-II adapter cannot connect with the selected protocol. Try set it to 0 - Automatic first. Then try from 1,2,3... Notice you have to wait some time for it to connect.
ELM327 v1.4 - переехал автомобиль. )))) купил ELM327 v1.5. пробовал на протоколе 0- automatic так и не заработало потом по пробовал на 4 - ISO 14230-4 KWP (5 baud init, 10.4 Kbaud) но тоже не помогло. Вам отправлял с обоих протоколов.
I see OBD logs only with two sessions (14.9.), both are reporting to be ELM327 v1.4 (in reality not ELM327 but a Chinese knock-off?). The other two sessions (13.9.) do not have logging turned on.
I think both setting 0 and 4 are wrong. It must be something else. It's same "UNABLE TO CONNECT" with both of the sessions.
hello, I have a white adapter ELM OBD2 from China. My car is toyota vitz 2003 . Your programm doesn't connect with ECU on my car. When I used the diagnistic program Torque, i wrote initialization string: atsp4\natiia13\natib96\natsh8113f1\natsw00\natat2 . In which way can I connect your programm witm my ECU
Hi, sorry I've forgot to reply the casper's message. Probably the same initialisation string would be needed in RaceChrono too. Right now there's no way to enter that string, but I will be working on the OBD-II during the spring / early summer, so I could add that too.
привет! так к сожалению OBD II и RaceChroha не заработала. Хотел спрошить, которую строчку отправлял "atsp4\natiia13\natib96\natsh8113f1\natsw00\natat2", не получилось добавить?
Unfortunately I had to do some unexpected additional work during the spring with the new iOS version, so I had to cancel the planned feature release, due to lack of time. I'll try to have the configurable initialisation, and other OBD-II improvements done during this winter.
Comments
The device all to see . When you click the Start GPS is OBDII then quickly turns red and try again to connect . or how can the other way to test the OBDII?
Now try to ISO 14230-4 KWP protocol ( 5 baud init, 10.4 Bbaud)
program except RC , not what is not open 100 % . After work, I will try to include Bluetooth fix we hope that will help .
Here for more accurate as possible? Yesterday tried everything on video and did not appear in the RPM setting is bird .
Сегодня в пробке попробовал как вы и написали. Не помогло к сожалению.
Настройки:
1.
3
4 (подключение OBDII только через протокол ISO14230-4 KWP ( 5 baud init, 10.4Kbaud )
5
6.
Can you send me the logs?
1) Turn on the "RaceChrono > Settings > Expert settings > Save device output" setting
2) Record a new session with the OBD-II reader configured, and send me the output file from phone's storage:
- RaceChrono: /Android/data/com.racechrono.app/files/sessions/session_(date)_(time)/device_(id)_output.obd
- RaceChrono Pro: /Android/data/com.racechrono.pro/files/sessions/session_(date)_(time)/device_(id)_output.obd
ELM327 v1.4
> ATE0
OK
> OK
> SEARCHING...
UNABLE TO CONNECT
> SEARCHING...
UNABLE TO CONNECT
> SEARCHING...
UNABLE TO CONNECT
> SEARCHING...
UNABLE TO CONNECT
> SEARCHING...
UNABLE TO CONNECT
Wrong protocol is selected, the OBD-II adapter cannot connect with the selected protocol. Try set it to 0 - Automatic first. Then try from
1,2,3... Notice you have to wait some time for it to connect.
I think both setting 0 and 4 are wrong. It must be something else. It's same "UNABLE TO CONNECT" with both of the sessions.